1:10 EP Truggy "AT3.4-V2" 4WD RTR

(No reviews yet) Write a Review
Calculated at Checkout
  • 1:10 EP Truggy "AT3.4-V2" 4WD RTR
  • 1:10 EP Truggy "AT3.4-V2" 4WD RTR
  • 1:10 EP Truggy "AT3.4-V2" 4WD RTR
  • 1:10 EP Truggy "AT3.4-V2" 4WD RTR
  • 1:10 EP Truggy "AT3.4-V2" 4WD RTR
  • 1:10 EP Truggy "AT3.4-V2" 4WD RTR
  • 1:10 EP Truggy "AT3.4-V2" 4WD RTR



The success story continues! We have equipped the AT3.4 "V2" with some new features that bring the vehicle to the next level of evolution.
Some technical changes have been implemented in our 1/10th scale truggy - among other things, the vehicle now comes with LED lighting on the roof
  • NEW* 80A brushed speed controller withT-connector and 540 motor
  • NEW* Programmable speed controller
  • NEW* 15kg steering servo with metal gears
  • NEW* LED lighting
  • NEW* Race body with many add-on parts
  • NEW* even more option parts available
The new 80A Brushed speed controller is waterproof, programmable and pre-configured with a T-connector. To fully exploit the potential of the vehicle, we recommend a 2S LiPo battery for operation. In addition, a separately available programming card (item 2110061) can be used to set various parameters such as braking force, punch, low voltage protection and more.

The car is powered by a 540size 15T brushed motor that directly accesses the all-wheel drive system. The two differentials (front and rear) are driven by an aluminum driveshaft. Due to the higher power of the speed controller and the use of T-connectors, any 2S LiPo battery can be used - no matter what the C-rate and capacity.
4 oil-pressure shock absorbers provide ideal handling, so there is plenty of driving fun. A 15kg metal gear servo with takes over the implementation of the steering commands.
Lightweight and compact design, as well as comfortable and ergonomically shaped - these are just two features of our CR4S 4-channel remote control. Of course, all trim, reverse and dual rate functions are available in the cockpit, making adjustments easy via levers and knobs. In addition, the remote control has a "Beginner Mode" (speed reduction by 50%) and is therefore ideal for pilots who do not yet have so much experience with the handling of such RC vehicles.
  • 4WD all wheel drive
  • 2.4 GHz 4-channel radio system
  • 80A brushed speed controller with T-plug
  • 540size 15T motor with 32.000RPM @ 7.4V
  • 15kg MG steering servo (25T, ball bearings)
  • Oil shock absorbers
  • Ball bearing main drive
  • Extremely durable composite plastic parts
  • Steel differential outputs
  • Aluminum main drive shaft with steel mounts
  • Adjustable upper tie rods
  • 5mm aluminum motor mount
  • 6mm shock towers
  • 2 differentials (front/rear)
  • Stylish truggy body with add-on parts
  • "Light-Weight" chassis (less weight - longer drive time)
  • Many aluminum option parts available
  • Scale: 1:10
  • Dimensions (L/W/H): 405x325x165 mm
  • Weight: 1740g
  • Wheelbase: 270mm
  • Ground clearance: ca. 35mm
  • Track width: 270mm front/rear
  • Wheels front/rear: Ø 105mm / Width: 55mm
  • Shock absorber oil: 400CPS
  • Shock absorber installation length: 90mm
  • Motor ratio: pinion: 18T / main gear: 64T (module 0,6) 
  • 1/10 Truggy "AT3.4V2" RTR
  • 2.4GHz "CR4S" radio
  • Sticker sheet
  • Manual
View AllClose